[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Anonymous wrote:

I like the gearbox crossmember!

I think it looks good and tucked up out the way on my gold vk the dam thing hung down pita

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Engine and gearbox mounts all done hopefully that’s it went right back to plumb bob down from sills both sides drew two lines parallel and squared a front line on the floor got the centre and made sure everything was parallel lucky i did it as was sitting 11mm out of parallel , engine and box are 7mm of centre

20200425_172539 by Frazer Russell[/url], on Flickr

20200425_172551 by Frazer Russell[/url], on Flickr

20200425_172622 by Frazer Russell[/url], on Flickr

20200425_172647 by Frazer Russell[/url], on Flickr

20200425_172715 by Frazer Russell[/url], on Flickr

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Top job Ian It’s looking the part now when’s start up to test that exhaust note     

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Hey all well got the aircon compressor all bolted up just had to take the lip of the chassis rail need to find a belt and weld two alloy pieces to the back of the bracket so i can bolt the back of compressor

20200421_172845 by Frazer Russell[/url], on Flickr

20200421_172859 by Frazer Russell[/url], on Flickr

20200421_172921 by Frazer Russell[/url], on Flickr

also had to make room for the reverse lock out solenoid used a bit of pipe, bolt and nut as could not get in with a hammer without dropping everything so put these things together ,, well you see on photo’s

photo of motor with angle gauge about 3-3.5

20200421_160907 by Frazer Russell[/url], on Flickr

20200421_160927 by Frazer Russell[/url], on Flickr

20200421_161148 by Frazer Russell[/url], on Flickr

20200421_161613 by Frazer Russell[/url], on Flickr

20200421_162131 by Frazer Russell[/url], on Flickr

20200421_173019 by Frazer Russell[/url], on Flickr

• This reply was modified 4 years, 8 months ago by  Judge1 Frazer.

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Looking up towards the Tararua ranges

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Cava when’s your going to start

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

You have been smashing it out Gary

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Well what a day started by removing the dash ,heater etc carpet out and sound deadening just fell off bit of surface rust to clean up ,so marked out the tunnel and cut a hole in it for the gearbox so have motor sitting at 3.5 degrees now , not sure on other builds but there must be a lot of ls’s conversions that have a lot of angle back 5 degrees or more as mine would not sit in there without modifying the tunnel ( I did remember with mine I have the larger and longer bellhousing for the twin plate clutch) anyway cuts mounts of the engine plates yesterday sit back in ready to tack again

20200419_154218 by Frazer Russell[/url], on Flickr

20200419_154225 by Frazer Russell[/url], on Flickr

20200419_154231 by Frazer Russell[/url], on Flickr

20200419_171748 by Frazer Russell[/url], on Flickr

20200419_171759 by Frazer Russell[/url], on Flickr

20200419_173449 by Frazer Russell[/url], on Flickr

20200419_173502 by Frazer Russell[/url], on Flickr

 

 

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Hey Gary any chance you could find out the degrees your engine sits back , straight edge on the face or the crank

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

VRSenator065 wrote:

Lol. One car person. It’s a disease….

Yeah 10 years time will see

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Cheers Gary

Yip really happy with the a/c mount will be able to use dipstick aswell just needs a bit of bending

going to post photos tomorrow but had to start again on the engine mounts as I set them up with the spacers taking Spacers out has throwing everything out, sump was siting on k-frame , engine mount bushes were binding up and sump was further away from k-frame was 5mm ended up 25mm   angels I suppose  , so cut the mounts of the block plates move engine in to the right position and go about welding them again , only thing is the engine is between 4.5-5 degrees( front to rear) and the gear box hits the tunnel so won’t go up any more, Ian has said that’s as far you wont to go , what hits is the service bolt and one way breather I think so I could dill a couple holes but not sure how much that would give me impossible to get in there to measure

photo’s tomorrow

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Cheers Ian

 

I see you have been flapping about  

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Hey Ian could I get away with the engine at 4.5-5.0 degrees taking the spacers out has screwed everything  gearbox hit tunnel so unless I start cutting tunnel ,, cheers

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

cava454 wrote:

Is that the factory LSA kit? Or an aftermarket setup?

Hay Cava it is the factory set up but modified to hell a bit of welding and a lot of time on the mill

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

hey all had some time in the garage today and just about got the a/c pump in just needs a few more adjustments

20200417_164645 by Frazer Russell[/url], on Flickr

20200417_164651 by Frazer Russell[/url], on Flickr

20200417_171835 by Frazer Russell[/url], on Flickr

20200417_171859 by Frazer Russell[/url], on Flickr

20200417_172834 by Frazer Russell[/url], on Flickr

 

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Hey Vin I wanted to sit the motor back further to help with the blower the more it goes back the less it stick out the front of bonnet it maybe 10-20mm but makes a huge difference ,, yes I could of gone the simple way but what fun is that

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Great work Ian love it can’t wait to hear and see it go

 

just no body look up BBF’s it could lead to the wrong place

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

vin wrote:

hey frazer, I could be wrong but just a idea/thought that might help for you to get measurement in a different way. I measured my 2 original kframes, a vc 6cyl and a vr/vs v8 and the measurement from the centre of power steering rack hole to the centre on top of original welded engine mounts is 190mm, both kframes are the same measurements. You made your own mounts and shifted location on kframe so if you measure yours now in the same manner I did and subtract from the 190mm, the difference would be the amount your engine is further back from standard engine location. Then you can measure back from your HB it will give you an idea on the sump length difference. Just an idea if it helps

Thanks vin

but since I have made everything from block mount to kframe I would need a reference from the motor some where , there is other way  for the measurement from what you just said gave me the idea  ,from the back of kframe or power steering hole to the back of sump or block that maybe an easer way

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

<del></del>Right see what you mean not something I would consider workshop is big enough I’m a one car kind of person

but maybe a mini later on

[Judge1 FrazerParticipant new zealand1983 VB LSA MG9 6060 6 speed View build HERE Member since: February 5, 2016 Posts: 775]

Heron SSV wrote:

I have CAE mounts on a VS V8 k frame. Sump is off a VX. The bottom of the sump is level with the bottom of the k frame. I can easily run my index finger around the sump on three sides in the gap between the sump and the k frame. Space is great, didnt need to modify the sump or k frame. Hope that helps.

Thank Heron but need measurements as I have modified my sump and it sits back just want to know how much

[Author]

Posts