[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

I’m in gas plant construction currently. NDT technician.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Now if only there was a way to remove the tensioner pulley up the top drivers side haha.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Plenty of people do it without a replacement pulley,  that looks cheap as imo.

 

Gary check fb inbox. I linked you a few different ways to run the belt.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

I usually shoot at around 1/60 – 1/80th of a second to get a decent amount of motion blur. F stop around 8-12 to get the whole car sharp. And ISO depends on the light at the time.

 

Hardest part of panning shots is getting the car in focus. If you have an entry level camera the auto focus can struggle to focus quickly.

 

Shoot in continuous mode for best results.

Shutter priority is probably the best mode to shoot in to begin with, rather than full manual. However SP mode usually drops the F stop quite low, meaning it’s difficult to get the whole car in focus.

 

This was shot at 1/80, f 5.0, iso 100, shutter priority.

 

 

 

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Jesus, don’t want much do you lol. Would almost be worth just taking the photo again.

But I like a challenge. I’ll do it tomorrow mate. Should be able to do everything requested.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

 

• This reply was modified 9 years, 10 months ago by  Jaba.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

It’s the main photo for the SC powercruise article as well.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Kroozer wrote:

Jaba wrote:

Will Be swapping to shannons with the next lot of work.

I’m with Shannons and they seem pretty good so far, a bit pricey though being under 25 :/

 

Can’t be that bad I already pay $300 a month.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Dunno lol, yet to be pulled over touch wood.

 

And insurance, I haven’t had a drama with anything, although they aren’t aware of anything.

Will Be swapping to shannons with the next lot of work.

 

 

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

VRSenator065 wrote:

Not sure if we have picked up any Photoshop experts yet?

:(

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Did you modify the AC line, or just heat it up and bend it so it sits closer to the strut tower?

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Looks immaculate! Beautiful.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

20% on back and sides, 35 on the screen.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

 

Cheers all!

Michael wrote:

How you liking the power with it now? Raced it yet?

Loving it mate, yet to race it. Being a bit of a pussy about it haha.

I’ll have to keep an eye out for a set of slicks.

• This reply was modified 9 years, 10 months ago by  Jaba.

[JabaParticipant Perth, WAVZ Senator View build HERE Member since: February 18, 2015 Posts: 103]

Awww, here’s me thinking I may have been the first! No more design work from me now!

[Author]

Posts