CommodoresPlus

well still getting there slowly, been a slow month

managed to finish painting the brakes, and refitting them the last week or so, also fitted up new front rotors and pads at the same time.

Also fitted up another K frame that i had Cleaned up and re-powder coated, and replaced both tie rod ends, due to one being cross threaded while it was…[Read more]

well still getting there slowly, been a slow month

managed to finish painting the brakes, and refitting them the last week or so, also fitted up new front rotors and pads at the same time.

Also fitted up another K frame that i had Cleaned up and re-powder coated, and replaced both tie rod ends, due to one being cross threaded while it was…[Read more]

im not sure if they will suit, but i currently have a set of 8, 36lb supercharged v6 injectors that have been reco’d and never used their currently on ebay too so you might have seen them already

i bought them for my 355, had them reco’d then got told wont need them

im not sure if they will suit, but i currently have a set of 8, 36lb supercharged v6 injectors that have been reco’d and never used their currently on ebay too so you might have seen them already

i bought them for my 355, then got told wont need them

Yeah Penrite hrp30 here too

Funny how they weld one model, and bolt others, my manta ones were out of a very original manta, and they were bolted in, and by brackets were bare steel, they had a bit of surface rust on them when I had to pull them back out after a few months so I cleaned them up and painted them

i still can’t work out why a vs manta which is a base model HSV…[Read more]

Funny how they weld one model, and bolt others, my manta ones were out of a very original manta, and they were bolted in, and by brackets were bare steel, they had a bit of surface rust on them when I had to pull them back out after a few months so I cleaned them up and painted them

i still can’t work out why a vs manta which is a base model HSV…[Read more]

Funny how they weld one model, and bolt others, my manta ones were out of a very original manta, and they were bolted in, and by brackets were bare steel, they had a bit of surface rust on them when I had to pull them back out after a few months so I cleaned them up and painted them

i still can’t work out why a vs manta which is a base model HSV…[Read more]

Funny how they weld one model, and bolt others, my manta ones were out of a very original manta, and they were bolted in, and by brackets were bare steel, they had a bit of surface rust on them when I had to pull them back out after a few months so j cleaned them up and painted them

i still can’t work out why a vs manta which is a base model HSV…[Read more]

My VS Hsv Manta ones are bolted in with some m8 (possibly m10) bolts by memory, you can just see one in this photo, managed to make it bigger

defiantly put them in properly, i recon you will damage the rear foams otherwise

My VS Hsv Manta ones are bolted in with some m8 (possibly m10) bolts by memory, you can just see one in this photo, sorry its the only photo i have.

defiantly put them in properly, i recon you will damage the rear foams otherwise

sold…………………..

Finishing on eBay tonight

If yours is a genuine clubby it should have knock sensor wiring, all vt 5lts run knock sensors

Vt ss wiring and computer is a different setup, you would be better off using your vs wiring and computer and you will need to swap over your to vs dizzy as the vt type is different too

Vt ss wiring and computer is a different setup, you would be better of  using your vs wiring and computer and you will need to swap over your to vs dizzy as the vt type is different too

Vt ss wiring and computer is a different setup, you would be better of  using your vs wiring and computer and you will need to swap over your to your vs dizzy as the vt type is different too

sold…………………..