Forum Replies Created
-
AuthorPosts
-
June 13, 2017 at 8:18 am #23144
$20 paint. $480 beer
June 13, 2017 at 7:57 am #23142Looking good mate. Bet your glad you went with the paint decision.
June 12, 2017 at 8:54 pm #23139Yeah mate. It was once turbo gas. Fuck me I was so impressed. We chopt a 460rwkw tt VY. The owner wasn’t happy. The throttle response is mind boggling
- This reply was modified 7 years, 5 months ago by cava454.
June 12, 2017 at 6:38 pm #23131Sounds like a sex toy
seriosuly. What’s it do. Lol
June 12, 2017 at 5:30 pm #23130Mint mate. That’s a nice cam. You will Be happy. How much the nitrous kit cost?
June 12, 2017 at 5:08 pm #23128I put $2 wedge led’s in mine. Much nicers
- This reply was modified 7 years, 5 months ago by cava454.
June 12, 2017 at 8:03 am #23118The VL rack has splines. The vs has like a square notch. That’s why u swap it over.
June 12, 2017 at 8:01 am #23117Fuck 70k. That’s basically time for a new engine.haha
Credit too you mate.
June 12, 2017 at 7:50 am #23116Haha yeah I no. Don’t worry I’ll be getting them done also. Went for a cruise last night in my mates VP Calais with LSA. fuck I was impressed
June 10, 2017 at 11:54 pm #23099Yep don’t doubt that. But it should come in pretty tidy on the bank balance. I have a knack for doing things cheap and I don’t mean cheap as in cutting corners etc.
June 10, 2017 at 9:41 pm #23097Undo the uni and swap the lower VL section onto the VS upper. Job done.
June 10, 2017 at 8:49 pm #23095Can still be done on a budget. You would be shocked if you knew what it owe me so far.
June 10, 2017 at 3:08 pm #23090Fuck u pricks costing me money. Gunna have to start a go fund me account.
No x bar on cage lol. Wanna keep the back seat. Granted it’s only registered as a 2 seater now.
- This reply was modified 7 years, 5 months ago by cava454.
June 10, 2017 at 12:57 pm #23086I’ll speak to fabricator about it also. Don’t forget I have cage today so the back half of the car is very solid.
The front end has also been stichwelded for extra support.
June 9, 2017 at 9:16 pm #23079You planning to reinforce the top trailing arm chassis mounts?
Dont think so. Should still eat ok I hope.
June 9, 2017 at 8:59 pm #23077That’s always a good sign hahaha
i hope mine scares me.
June 9, 2017 at 8:16 pm #230755 years is a good stint. Any plans for extra work or just freshen and leave as is.
June 9, 2017 at 8:10 pm #23074Yep shit. Lol I’m talking about my adjustable upper arms inregards to pinion angle
long week hahah
but Gary. What he said.
June 9, 2017 at 6:43 pm #23069Mines a master off a VZ. Maloo.
I will tee the front brake lines under the guard and the rear at the diff.
Bolts on using the same bracket you use for vt setup. Only slightly massaged.
All vz have abs. So not sure about the non abs master. Fill me in????
No installed photos gary. Plus mine was vague. Here’s the complete setup.
Goes across the chassis. With 2 arms bolted to tabs you Weld on the diff. Stops diff rolling forward.
June 9, 2017 at 6:38 pm #23068Nice. You don’t stuff around.
Collects a bit of dirt and dust don’t it.
-
AuthorPosts