HomeForumsMembers’ Builds and RidesVN – VP – VR – VSSlow355 B&m working with factory shift lights !!!!

This topic contains 232 replies, has 24 voices, and was last updated by Profile photo of Immortality Immortality 7 years, 4 months ago.

Viewing 20 posts - 21 through 40 (of 233 total)
  • Author
    Posts
  • #6401
    Profile photo of cava454
    cava454
    Moderator
    Member since: February 20, 2015
    Posts: 2 390
    Supporter

    U built nothing lol. U paid

    #6403
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    Yea reads that way, i mean i aint got no engine builder as A) he is retired and B) has done what i needed. I picked the combo etc last time, so hopefully this one works out, with those heads should be fine.

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #6404
    Profile photo of vs manta 218
    vs manta 218
    Participant
    Member since: March 2, 2015
    Posts: 796
    Supporter

    No need for mech roller. 288 will go 520hp no worries. Tried and tested.

     

    The one i listed is same as a 288 only difference is more lift

    So can only be better

    Its a new of the shelf grind released recently and ill bet it takes 288 spot

    #6405
    Profile photo of vs manta 218
    vs manta 218
    Participant
    Member since: March 2, 2015
    Posts: 796
    Supporter

    ^^^ oops didnt see the part about mechanical roller

     

    My bad, carry on

     

    If you ho flat tappet then year 288, if you go roller then i would go the new one but not sure if you can just slap a roller into a existing flat tappet

    #6466
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    Na u can’t, I’ll get a 288 kit soon. What roller rockers would be best without breaking the bank?

    • This reply was modified 9 years, 6 months ago by Profile photo of Slow355 Slow355.

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #6528
    Profile photo of vs manta 218
    vs manta 218
    Participant
    Member since: March 2, 2015
    Posts: 796
    Supporter

    Pretty  much  no

     

    Have you got 5/16 or 7/16 rocker studs ??

     

    Your talking up around 350-380lbs  open valve pressure (I think)

    dont think a affordable rocker is in existence except poo comp might have some puss

     

    an get yella terra street series 5/16 rockers  for like $640 ish and think that’s rated to 400lbs pressure and if you have 7/16 I’m not sure as platinum’s are about $42 thousand pesos if you happen to be in the Philippines or shit loads in oz

     

    maybe if crane gold series do a adjustable rocker would also be good but I’m not sure they do or not  :unsure:

     

    I personally would not trust any of the scorpion, home brand, Chinese rip offs at 380lbs at 6800rpm

     

    just go around and borrow cavas for the next 3 years or so   :yes:

    • This reply was modified 9 years, 6 months ago by Profile photo of vs manta 218 vs manta 218.
    #6545
    Profile photo of cava454
    cava454
    Moderator
    Member since: February 20, 2015
    Posts: 2 390
    Supporter

    What do u have now?

    If if what u have now aren’t up to the task buy Tony’s old ones. They need to be adjustable so we can set lash etc.

    #6554
    Profile photo of GMH-304
    GMH-304
    Participant
    Member since: March 13, 2015
    Posts: 39

    Na us can’t, I’ll get a 288 kit soon. What roller rockers would be best without breaking the bank?

    Any good quality 7/16 stud mount rocker will do the job. Hit up Engine Parts 24 Seven on ebay, he has Crane Cam kits, Crane Gold rockers and ARP rocker stud/Crane guide plate kit.

    #6636
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    Have street rollers on my heads at the moment but obviously will get something more suitable, just dont know how good i need to go. How do the yella terras n crane compare to each other?

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #6640
    Profile photo of vs manta 218
    vs manta 218
    Participant
    Member since: March 2, 2015
    Posts: 796
    Supporter

    Yella terra platinums would be far supperia to crane gold series

     

    I dont think crane golds come in adjustable

    Also they are not shaft mouted like yella terra

     

    Look up the specs of yours and if they are the adjustable ones and good for 400 lbs spring pressure they will do the job and next step from there is $1150 platinums

     

    When i built my engine i had a set of crane golds with intentions of goin a hydrolic cam but was advised by pavtek to go shaft mounted so i returned them as i only got them a week earlier and then it all blow out and i went solid cam as well

    #6688
    Profile photo of cava454
    cava454
    Moderator
    Member since: February 20, 2015
    Posts: 2 390
    Supporter

    Street terra adj will be fine.

    #6689
    Profile photo of GMH-304
    GMH-304
    Participant
    Member since: March 13, 2015
    Posts: 39

    Platinums are overkill for this. Stud mount rockers are adjustable and would be more than up too the task.

    #6700
    Profile photo of vs manta 218
    vs manta 218
    Participant
    Member since: March 2, 2015
    Posts: 796
    Supporter

    Yeah I also agree platinum’s are over kill for this

     

    I would stick with the street terra you have, biggest question are they 5/16 or 7/16 studs as I would want 7/16

     

    5/16 will probley still do fine,  I’m not sure what the recommendations are on this

    #6713
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    Na my street terrors not adjustable, yella terra just down the road from me if they still there ill have a look

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #8054
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    So finnaly came across a set of devonish front seats, got them for a great price and actually in really really good condition!! The ss seats were getting a little ruff. So i put them in the ute and actually look pretty decent for now although will have retrimmed. I have new ss seat material etc that i got off ebay a while ago. I know some people will not like. All the dash plastics that were painted blue 7 years ago will be sprayed gloss black. As realise that the blue is a little ricer. Steering wheel will be retrimmed and new carpet. The carpet is gray and thinking maybe going black.


    Not done much towards cam swap as been very busy with work and saving money for going overseas. Not in any crazy hurry with it as quite happy driving it as is.

    • This reply was modified 9 years, 4 months ago by Profile photo of Slow355 Slow355.

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #8060
    Profile photo of SLE355
    SLE355
    Participant
    Member since: April 7, 2015
    Posts: 119

    Seats look good!

    #8062
    Profile photo of cava454
    cava454
    Moderator
    Member since: February 20, 2015
    Posts: 2 390
    Supporter

    U already know what I think…

    #8254
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    Yes i know what u think cav you told me a thousand times haha. Will see how we go, most likely will be retrimmed as have the trim already.

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #11042
    Profile photo of Slow355
    Slow355
    Participant
    Member since: March 2, 2015
    Posts: 322

    So finally got some decent pics of the ute, came up pretty sweet.

    munch munch ls1s for lunch
    Best 1/4 mile 13.1@105mph 60ft-1.8sec Reaction time .8 sec 0/100-4.8sec

    #11044
    Profile photo of SLE355
    SLE355
    Participant
    Member since: April 7, 2015
    Posts: 119

    Good pics mate.

Viewing 20 posts - 21 through 40 (of 233 total)

You must be logged in to reply to this topic.

Skip to toolbar