Home›Forums›General›The Pool Room›Build Ninja – 3D Printing – *New Designs Available*
This topic contains 55 replies, has 17 voices, and was last updated by vspete 7 years ago.
-
AuthorPosts
-
November 14, 2017 at 12:32 am #25124
OZ38Participant- Jurien Bay W.A.
- VS & VY Sedan & Ute. Ecotec powered Hilux 4WD.
View build HERE
Posts: 59Do you have a couple more to load on ?
I am sure I saw something of yours on FB which was the gauge pod in the VR/VS Commy upper drivers door vent, as well as another for under the stereo with gauge(s) & a phone sized pocket ?
Cheers
Deek
November 14, 2017 at 12:31 pm #25125
VRSenator065Participant- Adelaide SA
- VR Senator LSx454 1960 Kombi (project) 1921 Nash Hot Rod (future project)
View build HERE
Posts: 5 777You are dead right, so I have just finished off a clip in replacement for the upper drivers door vent, tbh those vents to 2/10ths of stuff all anyway. I have angled them across and up, actually really nice to read.
I have also done one that takes a phone and two rocker switches. I dont have a phone of it instlled yet.
November 18, 2017 at 3:56 am #25149That looks real good in the vent nice work
November 19, 2017 at 4:17 pm #25167
VRSenator065Participant- Adelaide SA
- VR Senator LSx454 1960 Kombi (project) 1921 Nash Hot Rod (future project)
View build HERE
Posts: 5 777Thanks, I am actually going to fit mine to mine I think.
November 24, 2017 at 8:00 pm #25243A dual gauge pod that fits in where the centre vents have been deleted in a VR would be nice
November 25, 2017 at 9:36 am #25248
VRSenator065Participant- Adelaide SA
- VR Senator LSx454 1960 Kombi (project) 1921 Nash Hot Rod (future project)
View build HERE
Posts: 5 777^Will contact you IJ when I get a spare minute
December 21, 2017 at 3:56 pm #25485
BTS666.0Participant- rockhampton
- VZ SS stroked, turbo, t400......
View build HERE
Posts: 78Are you able to do a double din 3 gauge holder for where the stereo goes in a vz? I would want the gauges angled toward driver and the bottom half flat for switches.
...so I said "orange ya glad I didn't say banana?"........hahahaha.....hhhmmmm...pffft.....
December 21, 2017 at 4:42 pm #25486
VRSenator065Participant- Adelaide SA
- VR Senator LSx454 1960 Kombi (project) 1921 Nash Hot Rod (future project)
View build HERE
Posts: 5 777Sure can, but I need to get hold of a dash surround to work with so I can design it and test fit it. If anyone can post me one or drop one off to me happy to do one.
December 21, 2017 at 5:52 pm #25488
BTS666.0Participant- rockhampton
- VZ SS stroked, turbo, t400......
View build HERE
Posts: 78Ill go to the wreckers tomorrow, see if they have any. then i will just chop it down and post it to you.
...so I said "orange ya glad I didn't say banana?"........hahahaha.....hhhmmmm...pffft.....
December 22, 2017 at 9:59 am #25500
ChrisMParticipant- Melbourne Vic
- VN Calais LS1
View build HERE
Posts: 140Can your printer make the rear roof lining trim?
Cheers chris
December 22, 2017 at 11:43 am #25502
VRSenator065Participant- Adelaide SA
- VR Senator LSx454 1960 Kombi (project) 1921 Nash Hot Rod (future project)
View build HERE
Posts: 5 777Hi Chris, I dont think so, my printer will do basically a volume of 275mm x 275mm x 275mm. Its something though that people like Rare Spares should be looking at….
December 22, 2017 at 5:52 pm #25515
BTS666.0Participant- rockhampton
- VZ SS stroked, turbo, t400......
View build HERE
Posts: 78All the vy/z at the wreckers were stripped. will look around again after xmas.
...so I said "orange ya glad I didn't say banana?"........hahahaha.....hhhmmmm...pffft.....
December 22, 2017 at 6:57 pm #25516
MichaelParticipant- VY Calais 383ci GT42 turbo.
View build HERE
Posts: 208My new 3D printed dash for my HK (modelled off a HT/G dash because the Racepak fit better)
December 22, 2017 at 7:50 pm #25519Oh that’s fuckjng mint. Want that for mine.
My new 3D printed dash for my HK (modelled off a HT/G dash because the Racepak fit better)
December 23, 2017 at 5:10 pm #25525
ImmortalityParticipant- 97 HSV Senator 185i 02 VX L67 Calais
View build HERE
Posts: 535Very nice indeed.
December 25, 2017 at 5:51 am #25553Nice
-
AuthorPosts
You must be logged in to reply to this topic.